Tile Adhesives and Grouts
Vetoset CA541

Thickbed cementitious tile adhesive.


Laying tiles with irregular backing to cementitious substrates.
Laying tiles on irregular substrates.
Laying of large heavy tiles such as natural stone over a variety of substrate conditions.
Where the thick bed is needed.
For Granite, Marble, and Artificial Stone flooring.
Fast Download
Saveto Tile Adhesives & Grouts Professional Product Range Brochure
download (*.pdf 2.34Mb)
Technical Information
Product Description

Vetoset CA541 is a cement-based thick-bed tile adhesive that works with most types of tiles and flexible substrates. The product is composed of a blend of cement, carefully selected aggregates, special additives and polymers that provide Vetoset CA541 with its unique properties. The product is suitable for internal as well as external use.


  • Easy to apply single component.

  • High bed thickness.

  • Used internally and externally.

  • High bond strength.

  • Suitable for use with underfloor heating systems.

  • BS EN 12004:2010 as C1

  • ISO13007: 2010 as C1

Packaging & Coverage

Vetoset CA541 supplied in 50 Kg Bag. Yield: 36 Liters

Shelf Life & Storage

An original sealed container of Vetoset CA541 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

White or Grey Powder
Application Information
Instructions for use

Design Consideration

  • Do not apply at a temperature below 5ºC.
  • For heavy traffic areas, it is good practice to back butter the tile back surfaces with the adhesive to ensure 100% coverage.
  • For large format and heavy tiles where the weight of the tiles cannot be supported by the adhesive, the installation method shall follow a bottom-up approach, and If more than two rows of tiles are to be fixed simultaneously, the tiles are to be mechanically supported using temporary anchor nails in between tile gaps or by using inclined support stud.


Add to the mixing container 10-11 liters of water for each 50 Kg bag of Vetoset CA541. Add the powder to the water and mix with a mechanical mixer or low-speed heavy-duty electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Vetobond AB432 can be used to enhance the performance of the product and reach S2 classification.


Apply a layer of the adhesive onto the substrate using the flat edge of the trowel. Comb the adhesive with a suitable notched trowel horizontally to achieve a bed thickness of 4- 20 mm. Place the tiles with firm pressure to ensure proper contact with the adhesive.

It is always better to work in a manageable area that can be tiled within the open time of the adhesive. Leave the tiled surfaces for 24 hours before grouting.


Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.

Surface Preparation

The substrate should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, or any other substance that might impair the quality of bond with the substrate. 


Additional Information
Health & Sefety

Vetoset CA541 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetoset CA541 is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Ceramic TILE FIX

Weather resistant cementitious adhesive for ceramic tiles.


Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.


Pool Grout

Water resistant grout for swimming pool tile joints.


Porcelain TILE FIX

Polymer modified weather resistant adhesive for porcelain tiles.



High quality ceramic tile adhesive for projects.


view more
Featured Product
Vetotop CL530
Premixed 2 to 10 mm thick cementitious self leveling underlayment


Premixed 2 to 10 mm thick cementitious self leveling underlayment

Leveling of concrete slabs prior to the application of final floor coverings such as tiles and resinous systems.
As a substrate for vinyl tiles, parquet, carpet, and floor coverings that require super-flat substrates.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com